Support · 32 answers · 15 fixes
Dolphin Liberty.
Liberty 200, 300, 400 and 600: charging, the Clicker, the app and what to do when it stops.
Liberty 200/300/400 / Troubleshooting
Troubleshooting (8)
- Why is Eco Mode not working on my Dolphin Liberty?Program Eco Mode with a full battery. Keep holding Power (ON) through the purple flashes until the green LED blinks 3 times.
- Why does my Liberty power on but not move?Check the charge and water placement, clean the filters, inspect the tracks and brushes, and check Eco Mode on Liberty 300/400.
- Why can’t I access all of the features on my Liberty power unit?The features available on your Dolphin Liberty power unit depend on which robot model you own.
- Why isn't the Clicker working with my cordless robot?Pool noise, low battery charge, or mode settings can keep your robot from responding to the Clicker.
- Why is the cycle selector not working on Dolphin Liberty 300 and 400?Turn the robot on, hold Power (ON) for 3-6 seconds after the battery LED lights up, then release when the purple LED blinks 3 times.
- Why won't my Dolphin Liberty finish its cycle with a red LED on the power unit?Clean the filters, check for obstructions, fully charge the robot, and turn off Eco Mode on Liberty 300/400/600.
- Why doesn't my Liberty climb the walls?Clogged or poorly seated filters, slippery walls, unbalanced water and low temperatures can keep your Dolphin Liberty from climbing.
- How do I clean a clogged impeller on my Liberty?Follow the cleaning steps for your Liberty's safety clip setup, and confirm all LEDs are off before inspecting the impeller.
Liberty 200/300/400 / Use & Maintenance
Use & Maintenance (10)
- What is the safest way to use my Dolphin Liberty induction charger?Use the original Maytronics charger in a shaded, protected area with a 120V GFCI outlet, and never put the charger in water.
- How do I properly store my Liberty robot?After each cycle, clean the filter and connect the charger; for off-season storage, drain your Liberty and charge the battery to at least 50%.
- What settings are available on my Liberty 300/400?Dolphin Liberty 300 offers Eco Mode, Floor Only cycles and Clicker pickup; Liberty 400 also has app settings and End of Cycle Pickup.
- What is Eco Mode, and how do I set it?Eco Mode schedules short cleaning sessions so your robot can stay in the pool for up to a week before recharging.
- How do I remove my Dolphin Liberty from the pool?Use Click-Up to bring Liberty 300 and Liberty 400 to the waterline, or lift Liberty 200 out with its handle or included pick-up hook.
- Which filters come with my Dolphin Liberty?Dolphin Liberty models come with Net and Ultra-Fine filters installed, with additional filters and basket features that vary by model.
- What is the safest way to use my Dolphin Liberty?Remove your Dolphin Liberty before anyone enters the pool, turn it off before inspections, and keep the charger at least 12 ft from the pool edge.
- How do I get started with my Dolphin Liberty?Charge your Dolphin Liberty until all three battery bars are solid green, then press the power button for less than 4 seconds and place it in the pool.
- What is the Cycle Selector on my cordless Dolphin Liberty 300 and 400, and how do I set it?After the battery LED lights up, hold the power button for 3-4 seconds until it flashes purple 3 times to switch from Regular to Floor Only.
- How do I use the Clicker with my cordless robot?Shake the Clicker in the water for 3 to 5 seconds to retrieve a supported robot, or stop Liberty 600 and EON™ 100/120d mid-cycle.
Liberty 600 / Troubleshooting
Troubleshooting (5)
- Why isn't my Liberty 600 reaching the steps?Switch your Dolphin Liberty 600 out of Floor Only mode and use Regular or Ultra-Cleaning mode to reach the steps.
- Why does my Dolphin Liberty 600 start and then stop or show a red LED?Check charging, the impeller, driving system, filters and water temperature, and check the app if the power button LED is red.
- My Liberty 600 has stopped working. What should I do?Check that your Dolphin Liberty 600 is fully charged, fully underwater within 30 seconds of starting, and free of impeller or drive system obstructions.
- Why can't I pair my cordless robot with the Maytronics One app?The Maytronics One app currently supports only EON 100, 120d, and Liberty 600, so confirm your model before checking pairing settings.
- Why doesn't Wi-Fi stay connected to the Maytronics One app?Dolphin robots do not stay connected to Wi-Fi or Bluetooth while operating underwater.
Liberty 600 / Use & Maintenance
Use & Maintenance (9)
- How do the features on my Liberty 600 work?Your Dolphin Liberty 600 offers app controls, Eco Mode scheduling, step and sun-ledge cleaning, and parking at a preferred wall.
- How does the Liberty 600 charge?The Liberty 600 uses a conductive charger, takes about 4.5 hours from low to full charge, and shows solid green when fully charged.
- What do the LEDs on my Liberty 600 mean?The front LED is decorative, while the panel LEDs show charging, low battery, temperature alerts, malfunctions, and cleaning status.
- How do I get started with my Liberty 600?Fully charge your Dolphin Liberty 600, connect it to the MaytronicsOne app, then place it in at least 3 feet of water to start cleaning.
- Why doesn't my cordless robot respond to the app while underwater?Your cordless robot disconnects from Wi-Fi and Bluetooth underwater, so select its cleaning program in the app before placing it in the pool.
- How do I set Eco Mode on my Liberty 600?Select Eco Mode with the robot's Mode Selector button, or use the MaytronicsOne App to choose a half-week, one-week, or two-week schedule.
- What cleaning modes are available with my Liberty 600?The Dolphin Liberty 600 offers four cleaning modes: Full Coverage, Floor Only, Ultra-Clean and Eco Mode.
- How do I connect to the Maytronics One App for the first time?Download the Maytronics One App and pair your robot over Bluetooth with the charger disconnected; 2.4 GHz Wi-Fi setup is optional.
- How do I set or change the Homing Wall?Set the Homing Wall in the MaytronicsOne app after 2-3 cleaning cycles, and change it only after the robot parks at its current Homing Wall.
No answers match. Try a different word, or .
More support
Fixes by model, parts and manuals.
Troubleshooting by robotA problem-first guide for every Dolphin and Niya robot.Fix a problem
Replacement parts241 genuine parts with the robots each one fits.Find a part
Dolphin manuals and guidesUser manuals, quick-start guides and how-to videos.Find your manual
Every answerAll topics, searchable.Browse answers
